全文获取类型
收费全文 | 794篇 |
免费 | 390篇 |
国内免费 | 149篇 |
专业分类
航空 | 906篇 |
航天技术 | 93篇 |
综合类 | 66篇 |
航天 | 268篇 |
出版年
2024年 | 8篇 |
2023年 | 21篇 |
2022年 | 38篇 |
2021年 | 48篇 |
2020年 | 38篇 |
2019年 | 35篇 |
2018年 | 30篇 |
2017年 | 60篇 |
2016年 | 55篇 |
2015年 | 42篇 |
2014年 | 46篇 |
2013年 | 36篇 |
2012年 | 54篇 |
2011年 | 40篇 |
2010年 | 38篇 |
2009年 | 33篇 |
2008年 | 58篇 |
2007年 | 73篇 |
2006年 | 85篇 |
2005年 | 44篇 |
2004年 | 61篇 |
2003年 | 42篇 |
2002年 | 36篇 |
2001年 | 47篇 |
2000年 | 40篇 |
1999年 | 36篇 |
1998年 | 27篇 |
1997年 | 28篇 |
1996年 | 21篇 |
1995年 | 24篇 |
1994年 | 15篇 |
1993年 | 20篇 |
1992年 | 9篇 |
1991年 | 10篇 |
1990年 | 7篇 |
1989年 | 12篇 |
1988年 | 8篇 |
1987年 | 8篇 |
排序方式: 共有1333条查询结果,搜索用时 15 毫秒
21.
22.
23.
采用气相渗硅工艺(GSI)制备C/C-Si C复合材料,研究了C/C素坯密度对GSI C/C-Si C复合材料物相组成与摩擦磨损性能的影响,分析了C/C-Si C复合材料的制动过程,并归纳了其摩擦磨损机理。结果表明,随着C/C素坯密度的增大,GSI C/C-Si C复合材料的密度呈递减趋势,且C含量和开气孔率逐渐增加,而Si C含量和残余Si含量逐渐减少;自对偶条件下,复合材料的平均摩擦系数、磨损率均呈现先增大后减小的趋势,当C/C素坯密度为1.25g/cm3时有最大值,而制动稳定系数则不断增大。GSI C/C-Si C复合材料的制动过程是犁沟效应和粘着效应共同作用的结果,制动初始阶段和刹停阶段以犁沟效应为主,中间阶段以粘着效应为主。 相似文献
24.
A cathode mandrel with translational and rotational motion, which was supposed to obtain uniform friction effect on surface, was employed in abrasive-assisted electroforming for revolving parts with complex profile. The effects of current density, translational speed and rotational speed on the deposit properties were studied by orthogonal test. The tensile strength, elongation and micro hardness value were measured to find out how the factors affected the properties. The optimized results show that changes of current density affect the tensile strength of nickel layer most, while translational speed has the most remarkable influences on both elonga-tion and micro hardness. The low rotational speed affects the properties least. In this experiment, a smooth nickel layer with tensile strength 581 MPa, elongation 17%and micro hardness 248HV is obtained by the orthogonal test. 相似文献
25.
以丁腈橡胶(CTBN)为增韧剂对环氧树脂(F51)进行增韧改性,通过FTIR、TG以及力学性能测试研究了丁腈橡胶对环氧树脂固化反应、热稳定性能和力学性能的影响,并分析了其增韧机理;分别采用燃气流剪切烧蚀试验和电弧风动烧蚀实验考核了低密度烧蚀材料的烧蚀性能。结果表明:经CTBN改性后,两者的分子链产生了一定程度的交联;树脂基体的拉伸、弯曲性能有所下降,但韧性得到了增强;热稳定性大大提高,增韧后的F51树脂在800℃时的残重率由增韧前的23%提高到了54%;低密度烧蚀材料的抗剪切、抗剥蚀能力得到了增强,且碳层的尺寸稳定性也得到了改善,烧蚀性能提高。 相似文献
26.
27.
28.
对于飞翼布局的飞行器,棱边的数量、长度、位置等因素影响着它的隐身性能。数值化地描述这些棱边关系并建立他们和隐身特性之间的联系,能够给飞行器综合一体化设计提供参考,为优化设计确认目标函数,提出了基于飞翼平面布局的棱边平行度数值化描述方法,根据建立的棱边关系和平行度之间的计算公式,分析了飞翼布局中棱边的数量、长度、位置等对平行度的影响。采用创建特征模型的方法,计算各个特征布局的雷达散射截面(RCS),结合所提出的平行度,给出了平行度与隐身特性之间的对应关系曲线并归纳了隐身特性对平行度的敏感度。总结出了通过增大平行度来提高隐身特性可以采取的措施,以及布局方案细微调整时需要注意的极值点。 相似文献
29.
30.